The 2 ram inground lifts offer powerful and well-engineered lifting technology.

• Installation cassette with hot-dip galvanized profile steel frame
• Hard chromed guide pistons (starting at 2.40 MKK - double guide- and hydraulic pistons)
• Electro-hydraulic drive, external from lifting unit
• Mechanical synchronisation via yoke which is at the same time safety device
• Synchronisation upon lowering via adjustable restrictor valves (ram distance 2.500 mm)
• Electronic control with stop valve
• Connection nozzle for KG-pipe DN 100 for cassette ventilation and as supply line ductwork
• Cassette cover cpl. hot-dip galvanized
• GS-approved, DIN EN 1493, CE-approved, Protection class IP 54
• Lift has to be combined with a chassis!

Application areas

• Body repair
• Automotive industry
• Explosion-Protection-Zones
• Ergonomic workplace design
• Paints shop
• Garage & Tyre-Service
• etc.

on request

The ultra flat scissor lifts (driven by electric power only) convince through their extremely flat design and this way ensure the lifting of sporty vehicles with an overall weight from 3,000 kg up to 4,000 kg.

• Platforms made from slip-resistant bulp plate
• Integrated electro hydraulic drive
• Dual hydraulic system - double cylinder in every scissor, no air supply necessary
• Safety signal tone during lowering in foot area
• Dead-man control
• With emergency lowering device and overload protection
• Tracks adjustable in length with flap mechanism, can be operated from the side
• Base frame hot-dip galvanized and galvanized ramps
• Incl. 4 elastomer adapters 20 mm
• Protection class IP54, GS-approved, DIN EN 1493, CE-approved

0.30 KH

• Mechanical synchronisation
• Optional: mobile set (1 connecting rod, 2 mountable guide rollers)

0.32 SDE, 0.35 SDE & 0.40 SDE

• Hydraulically synchronisation of tracks with cylinder follow-up principle
• No mechanical linkage between the tracks
• All hinge points are equipped with lubricating bolts
• Inground installation possible without additional accessories

Also available as Ex-protected version

References of various car manufacturers are available for 4 post lifts. Custom made design models on request. All 4 post lifts are generally suitable for wheel alignment and can be equipped with a wheel alignment set.

• Low noise hydraulic under oil drive
• Electro-hydraulic control
• Separated main switch (can be locked as required by CE)
• Acoustic foot protection
• Hydraulic traction cylinder
• Slack cable and cable failure safety feature and roll back protection
• Platform with 1.000 mm drive-on ramps for sporty vehicles
• One platform fully adjustable, with locking mechanism
• Integrated rail for jacking beam
• Central control for pneumatic locking device (8 bar)
• Locking bars for overall lifting height with locking device each 100 mm
• Integrated wheel free scissor with extendable support (for SN versions)
• Wheel free scissor with Master / Slave hydraulic system (for SN versions)
• Inclusive elastomer pick ups (20 mm for SN, 60 mm for SN-AM versions)
• Integrated full size slide plates (for AM versions)
• System for turn tables up to 50 mm height, with serial turn table cover (for AM versions)
• Optional with post clearance 3.000 mm
• Protection class IP54, GS-approved, DIN EN 1493, CE-approved

The 2 post lifts convince through their robustness, stability and reliability. Traditional manufacturing technology, lowest swivel in heights and the chance to reach original lifting points of car manufacturers with most of these lifts, make them valuable partners for professional workshops. In proven use at all notable car manufacturers.

• Special rolled section columns, no sheet metal
• Installation rectangular to drive-on direction
• Carriage guided by 6 rollers
• Bronze load nut / cast alloy safety nut
• Oil dispenser for supporting lubrication
• Broken nut raise lock-down features
• Acoustic foot protection
• Softline push button control with computer guided leveling system
• Lockable main switch directly on the post
• Complete covering of post interior
• Cushioning door stop, adjustable pick up plate (approx. 25 mm)
• Arm locking device (easily adjustable), locking at 300 mm
• Optional: self-supporting base frame; 2nd control unit
• Protection class IP54, GS-approved, DIN EN 1493, CE-approved