Specially developed cleaning foam for pre-treatment

Strongly recommended before using marten repellents!


Easily removes the marten’s scent mark, with no need for risky engine washing. Safe for electronic components as well as for paint, rubber and plastic.


When the engine is cool, spray the entire engine compartment as well as the underside of the bonnet and the mudguards thoroughly.


Use the whole can and allow the foam to take effect for a short while. Then simply rinse with water – no pressure washer or powerful water jet needed.
 

• Highly adhesive active foam
• Very easy to use
• Safe for plastic, rubber and paint

Item code 07503

Insulation-displacement contact technology (SKT) – no need to connect to on-board power supply – ultrathin design

High-voltage ultrasonic combination device with six PLUS-MINUS SKT stainless steel contact plates.

Looking to achieve high voltage in record time? Then look no further than STOP&GO! Sophisticated insulation-displacement contact technology (SKT) enables the PLUS and MINUS high-voltage stainless steel contact plates to be installed quickly without any screws. Our contact plates have been tried and tested for over ten years and have now been optimised with two additional contact tips.

Thanks to SKT, simply pushing together the plates establishes contact between a spike and the two-pole high-voltage cable. The PLUS and MINUS two-pole design ensures that an electric shock is produced, regardless of the materials used in the engine compartment. This safe but very effective electric shock (electric fence principle) will keep martens away from even modern vehicles that have many parts made of non-conductive materials such as plastic.

Additional options for attaching the stainless steel contact plates make installation even easier and offer additional flexibility. This is especially beneficial as engine compartments are becoming more and more compact. The connection to terminal 15 has been replaced by innovative sensor technology, and a slide contact attached directly to the device eliminates the need to install a bonnet contact switch.

• Battery operated
• Sensor technology
• Power consumption: approx. 0.4 mA
• Up to 18 months of operational life
• 6 stainless steel contact plates with a plus and minus pole and SKT
• 2 waterproof piezo speakers
• Dispersion radius: 360°
• Dispersion angle: > 170°
• Sound pressure: approx. 110 dB
• Frequency modulation to prevent habituation
• Function control light, blinking LED
• Waterproof in accordance with IP65
• Panic protection control
• Also suitable for home and carport
• E1 marking by the German Federal Motor Transport Authority (KBA)

Item code 07542

Insulation-displacement contact technology (SKT) – connects to on-board power supply – ultrathin design

High-voltage ultrasonic combination device with six PLUS-MINUS SKT stainless steel contact plates.

Looking to achieve high voltage in record time? Then look no further than STOP&GO! Sophisticated insulation-displacement contact technology (SKT) enables the PLUS and MINUS high-voltage stainless steel contact plates to be installed quickly without any screws. Our contact plates have been tried and tested for over ten years and have now been optimised with two additional contact tips.

Thanks to SKT, simply pushing together the plates establishes contact between a spike and the two-pole high-voltage cable. The PLUS and MINUS two-pole design ensures that an electric shock is produced, regardless of the materials used in the engine compartment. This safe but effective electric shock (electric fence principle) will keep martens away from even modern vehicles that have many parts made of non-conductive materials such as plastic.

Additional options for attaching the stainless steel contact plates make installation even easier and offer additional flexibility. This is especially beneficial as engine compartments are becoming more and more compact. The connection to terminal 15 has been replaced by sensor technology, and a slide contact attached directly to the device eliminates the need to install a bonnet contact switch.
 

• 12-volt connection
• Sensor technology
• Power consumption: approx. 0.4 mA
• 6 stainless steel contact plates with a plus and minus pole and SKT
• 2 waterproof piezo speakers
• Dispersion radius: 360°
• Dispersion angle: > 170°
• Sound pressure: approx. 110 dB
• Frequency modulation to prevent habituation
• Function control light, blinking LED
• Waterproof in accordance with IP65
• Panic protection control
• Compatible with CAN data bus
• E1 marking by the German Federal Motor Transport Authority (KBA)

Item code 07571

Ultrasound with frequency modulation – no need to connect to on-board power supply – ultrathin design

Highly effective, battery-operated ultrasonic device. Frequency modulated ultrasonic tones mimic animal fear and warning cries, signalling extreme danger to the marten. No habituation effect.

Operated with two standard 3-volt button batteries (CR2477), making it independent of the on-board power supply. Especially long operational life of approx. 24 months per battery set. Ideal for vehicles that remain parked for long periods such as classic cars, motor homes and exhibition vehicles as well as for carports.
 

• Uses 2 standard CR2477 3-volt button batteries
• Up to 24 months of operational life
• 2 waterproof piezo speakers
• Dispersion radius: 360°
• Dispersion angle: > 170°
• Sound pressure: approx. 110 dB
• Frequency modulation to prevent habituation
• Function control light, blinking LED
• Waterproof in accordance with IP65
• E1 marking by the German Federal Motor Transport Authority (KBA)

Item code 07533

Specially developed cleaning foam for pre-treatment

Strongly recommended before using marten repellents!


Easily removes the marten’s scent mark, with no need for risky engine washing. Safe for electronic components as well as for paint, rubber and plastic.


When the engine is cool, spray the entire engine compartment as well as the underside of the bonnet and the mudguards thoroughly.


Use the whole can and allow the foam to take effect for a short while. Then simply rinse with water – no pressure washer or powerful water jet needed.
 

• Highly adhesive active foam
• Very easy to use
• Safe for plastic, rubber and paint

Item code 07503

Insulation-displacement contact technology (SKT) – no need to connect to on-board power supply – ultrathin design

High-voltage ultrasonic combination device with six PLUS-MINUS SKT stainless steel contact plates.

Looking to achieve high voltage in record time? Then look no further than STOP&GO! Sophisticated insulation-displacement contact technology (SKT) enables the PLUS and MINUS high-voltage stainless steel contact plates to be installed quickly without any screws. Our contact plates have been tried and tested for over ten years and have now been optimised with two additional contact tips.

Thanks to SKT, simply pushing together the plates establishes contact between a spike and the two-pole high-voltage cable. The PLUS and MINUS two-pole design ensures that an electric shock is produced, regardless of the materials used in the engine compartment. This safe but very effective electric shock (electric fence principle) will keep martens away from even modern vehicles that have many parts made of non-conductive materials such as plastic.

Additional options for attaching the stainless steel contact plates make installation even easier and offer additional flexibility. This is especially beneficial as engine compartments are becoming more and more compact. The connection to terminal 15 has been replaced by innovative sensor technology, and a slide contact attached directly to the device eliminates the need to install a bonnet contact switch.

• Battery operated
• Sensor technology
• Power consumption: approx. 0.4 mA
• Up to 18 months of operational life
• 6 stainless steel contact plates with a plus and minus pole and SKT
• 2 waterproof piezo speakers
• Dispersion radius: 360°
• Dispersion angle: > 170°
• Sound pressure: approx. 110 dB
• Frequency modulation to prevent habituation
• Function control light, blinking LED
• Waterproof in accordance with IP65
• Panic protection control
• Also suitable for home and carport
• E1 marking by the German Federal Motor Transport Authority (KBA)

Item code 07542

Insulation-displacement contact technology (SKT) – connects to on-board power supply – ultrathin design

High-voltage ultrasonic combination device with six PLUS-MINUS SKT stainless steel contact plates.

Looking to achieve high voltage in record time? Then look no further than STOP&GO! Sophisticated insulation-displacement contact technology (SKT) enables the PLUS and MINUS high-voltage stainless steel contact plates to be installed quickly without any screws. Our contact plates have been tried and tested for over ten years and have now been optimised with two additional contact tips.

Thanks to SKT, simply pushing together the plates establishes contact between a spike and the two-pole high-voltage cable. The PLUS and MINUS two-pole design ensures that an electric shock is produced, regardless of the materials used in the engine compartment. This safe but effective electric shock (electric fence principle) will keep martens away from even modern vehicles that have many parts made of non-conductive materials such as plastic.

Additional options for attaching the stainless steel contact plates make installation even easier and offer additional flexibility. This is especially beneficial as engine compartments are becoming more and more compact. The connection to terminal 15 has been replaced by sensor technology, and a slide contact attached directly to the device eliminates the need to install a bonnet contact switch.
 

• 12-volt connection
• Sensor technology
• Power consumption: approx. 0.4 mA
• 6 stainless steel contact plates with a plus and minus pole and SKT
• 2 waterproof piezo speakers
• Dispersion radius: 360°
• Dispersion angle: > 170°
• Sound pressure: approx. 110 dB
• Frequency modulation to prevent habituation
• Function control light, blinking LED
• Waterproof in accordance with IP65
• Panic protection control
• Compatible with CAN data bus
• E1 marking by the German Federal Motor Transport Authority (KBA)

Item code 07571