The complete new universal programmable Battery Guard (BGW) prevents excessive discharge of the battery (which would damage the battery) and protects electronic appliances against overvoltage. The BGW 60 battery guard has an “Automatic Board System Detection”; the BGW automatically detects the battery voltage (12 or 24V). The BGW 60 battery guard is capable of carrying 60A continuous load and 300A peak current @ 25 degrees. You can choose between 10 on/off threshold voltage programmes, for both 12V and 24V battery systems, which can be easily programmed.

The original alternator program used to be 14.4V/28.8V as long as the engine was running and manufacturers have developed charge programs to reduce energy and hence fuel wastage. Different vehicle manufacturers use different charging profiles but even the same manufacturers continuously update their charge programs. The ELOGIC DC-DC battery charger are primarily intended to charge an auxiliary or service battery from a vehicle starter battery. The input battery voltage can be above, below or equal to the output battery voltage. So the ELOGIC DC-DC battery charger allows the auxiliary battery to be perfectly charged regardless of the input voltage, while being protected against damage due to peak voltages.

This advanced fully automatic 4-stage 50 Amp battery charger is ideal for charging all types of 12 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell), and Lithium/LiFePO4 batteries from a 115/230 V, 50/60 Hz AC source. A DIP switch setting can be used to convert to a two stage algorithm, in order to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. 4 different kind of Lithium charging characteristics are easily to be selected by the DIP switches. Features include overload and short circuit protection. The unit allows charging of up to 2 separate battery banks.

This highly efficient DC-AC inverter converts 12 Volts DC to 1600 Watts of pure sine wave AC power at 230 Volts, 50 or 60 Hz. The unit is having heavy duty hex screw M8 connection. Features include overload protection, low battery alarm / shut down, low idle power draw of less than 1.6 Amps. AC power is available from a single standard 2x VDE European outlet, accessible on the front panel. Various possibilities for using a remote control and high surge power makes this new SAMLEX DC-AC pure sinewave inverter a real winner. E-approved

The BSWM -160 DUAL is designed for use in situations where 2 batteries are used; for example in boats, campers and caravans. The Battery separator is a microprocessor controlled high capacity mechanical switch with vibration (i.e. motion) detection. Since every vehicle (EURO 5/6 engines) has its own vibration frequency and amplitude, the user can set the sensitivity of the BSWM however it can also be used in vehicles with the “old” type of alternators. IP-67 and E-approved.

The complete new universal programmable Battery Guard (BGW) prevents excessive discharge of the battery (which would damage the battery) and protects electronic appliances against overvoltage. The BGW 60 battery guard has an “Automatic Board System Detection”; the BGW automatically detects the battery voltage (12 or 24V). The BGW 60 battery guard is capable of carrying 60A continuous load and 300A peak current @ 25 degrees. You can choose between 10 on/off threshold voltage programmes, for both 12V and 24V battery systems, which can be easily programmed.

The original alternator program used to be 14.4V/28.8V as long as the engine was running and manufacturers have developed charge programs to reduce energy and hence fuel wastage. Different vehicle manufacturers use different charging profiles but even the same manufacturers continuously update their charge programs. The ELOGIC DC-DC battery charger are primarily intended to charge an auxiliary or service battery from a vehicle starter battery. The input battery voltage can be above, below or equal to the output battery voltage. So the ELOGIC DC-DC battery charger allows the auxiliary battery to be perfectly charged regardless of the input voltage, while being protected against damage due to peak voltages.

This advanced fully automatic 4-stage 50 Amp battery charger is ideal for charging all types of 12 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell), and Lithium/LiFePO4 batteries from a 115/230 V, 50/60 Hz AC source. A DIP switch setting can be used to convert to a two stage algorithm, in order to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. 4 different kind of Lithium charging characteristics are easily to be selected by the DIP switches. Features include overload and short circuit protection. The unit allows charging of up to 2 separate battery banks.