Description

High quality 2K acrylic primer with anti-corrosion additives. It is a perfect isolating primer for car repairs. Perfetly protects sanded bare steel and isolates difficult surfaces and putties from topcoats, preventing mapping effects. Ideal spreading and fast drying time allows primer to be applied wet on wet. Does not require sanding.

Advantages

• Very good anticorrosive protection. of steel surfaces.
• Strong adhesion to various substrates.
• Very good isolating properties.
• Short hardening time.
• Suitable for wet on wet application.

Substrates

Wet on Wet Acrylic Primer 3:1 can be applied over:

• Steel and aluminum after flatting and degreasing.
• Zinc coated steel and galvanized steel after flatting and degreasing. S
• anded glass polyester laminates (GFK/GRP). P
• olyester body fillers and putties
• Epoxy primers.
• Wash primers.
• Old coatings in good condition.

Description

2-component polyurethane protective coating with a structure effect.

Advantages

• Protective coating with excellent chemical (oil, gasoline, water, salt) and mechanical resistance (scratches, stains).
• Resistant to weather conditions (UV filters) and corrosion (anti-corrosive agents).
• Can be painted on various substrates. It can be applied with the UBS antigravel gun as well as with a conventional gravity spray gun.

Substrates

• Steel, galvanized steel, stainless steel, aluminum – prime surfaces with a 2K epoxy primer or 2K acrylic primer, sand using abrasive paper with gradation from P180 to P320, clean and degrease (Silicone Remover Troton).
• Polyester laminates – sand using abrasive paper P180 or by using Troton’s unwoven abrasive fabric, clean and degrease (Silicone Remover Troton).
• Polyester body fillers – sand using abrasive paper with gradation from P120 to P240, clean and degrease (Silicone Remover Troton).
• Plastic surfaces – degrease (Silicone Remover Troton), sand with abrasive paper P240 or with Troton’s unwoven abrasive fabric, degrease again (Silicone Remover Troton), prime with an adhesive promoter, such as Plastic Primer Troton. Due to the many different types of plastic, adhesion testing is advised. Do not apply the product directly on bare metal. Rangers should be applied on primed surfaces or on 2K topcoats and basecoats after proper preparation (be careful with the application on old coatings, thinner testing is advised). Always abrade, clean and degrease the surface before application.
• Do not apply the product on 1K primers. Instead, always prime the surfaces for the Rangers application with a 2k acrylic primer, 2K epoxy primer or 2k etching primer. Always wait the proper drying and hardening time of etching primer before application.
• Do not apply Rangers directly on bare original paint or directly on coatings of car body parts from the aftermarket.

Kit content:

• T1 STRONG POLISHING COMPOUND 250g
• T2 ANTIHOLOGRAM & MICROSCRATCH REMOVER 250g
• T3 QUICK WAX 500 ml
• T4 PROTECT LIQUID 250 ml

BRAYT T1 STRONG is a polishing compound dedicated to all types of varnish used in automotive and industry sector, including hard scratch resistant coatings (e.g. ceramic). Product is recommended to fresh polymerized coats and for old paint coatings. Removes easily scratches and sanding traces (abrasive paper 1500). Doesn’t contain fillers and silicones.

• Cut level 8/10
• Gloss level 8/10

BRAYT T2 Compound is designed for removing holograms and microscratches on painted surfaces as well as traces made in sanding process. Product guarantees ideal deep gloss, creates protective layer resistant to detergents on the surface of the clear coat. Doesn’t contain the silicone.

• Cut level 4/10
• Gloss level 10/10

BRAYT T3 QUICK WAX & SHINE simple and easy to use based on waxes, dedicated to all types of smooth and shiny surfaces (varnished, glass, plastic). It is possible with product to achieve gloss and color depth, surface becomes slippery. It shows great hydrophobic, nurturing and preserving properties. Doesn’t leave marks on plastic and rubber.

Properties: Gloss level 10/10

BRAYT T4 emulsion for surface refreshment, leaves invisible protective layer against impurities. Extends the freshness of the clear coat in 40-50%, decreases impurities on the car body up to 70-80%. Product might be used to protect varnished surfaces, gelcoats and polycarbonates. T4 has also light abrasive properties what allows to remove small defects and holograms. Suitable to gelcoats and each type of clear coats (acrylic, water based, bicomponent and fabric coatings), also on ceramic scratch resistant coatings. Enhances gloss, prevents the oxidation of the varnish, protects against UV rays, acid rain, resin. To achieve high gloss without the mist and holograms, soft foam is dedicated.

• Cut level 2/10
• Gloss level 10/10

Description

High-quality 2K acrylic clear coat with very low VOC content for quick car paint repairs. The product was specially developed for car repair shops that want to return the repaired car to the owner as soon as possible. The use of the latest generation of raw materials allows for very short curing times of the paint. When using a paint with a quick hardener, the painted element can be installed after 60 minutes (at 20°C)!

Advantages

• Short curing time / reduction in repair time
• Very high resin content (VOC 355 g/l)
• High hardness and mechanical resistance
• High gloss
• Perfect appearance of the coating
• Substrate

Acrylic paints can be applied:

• on base coats
• on sanded and degreased old paint coatings in good condition

Description

High quality 2K acrylic primer with anti-corrosion additives. It is a perfect isolating primer for car repairs. Perfetly protects sanded bare steel and isolates difficult surfaces and putties from topcoats, preventing mapping effects. Ideal spreading and fast drying time allows primer to be applied wet on wet. Does not require sanding.

Advantages

• Very good anticorrosive protection. of steel surfaces.
• Strong adhesion to various substrates.
• Very good isolating properties.
• Short hardening time.
• Suitable for wet on wet application.

Substrates

Wet on Wet Acrylic Primer 3:1 can be applied over:

• Steel and aluminum after flatting and degreasing.
• Zinc coated steel and galvanized steel after flatting and degreasing. S
• anded glass polyester laminates (GFK/GRP). P
• olyester body fillers and putties
• Epoxy primers.
• Wash primers.
• Old coatings in good condition.

Description

2-component polyurethane protective coating with a structure effect.

Advantages

• Protective coating with excellent chemical (oil, gasoline, water, salt) and mechanical resistance (scratches, stains).
• Resistant to weather conditions (UV filters) and corrosion (anti-corrosive agents).
• Can be painted on various substrates. It can be applied with the UBS antigravel gun as well as with a conventional gravity spray gun.

Substrates

• Steel, galvanized steel, stainless steel, aluminum – prime surfaces with a 2K epoxy primer or 2K acrylic primer, sand using abrasive paper with gradation from P180 to P320, clean and degrease (Silicone Remover Troton).
• Polyester laminates – sand using abrasive paper P180 or by using Troton’s unwoven abrasive fabric, clean and degrease (Silicone Remover Troton).
• Polyester body fillers – sand using abrasive paper with gradation from P120 to P240, clean and degrease (Silicone Remover Troton).
• Plastic surfaces – degrease (Silicone Remover Troton), sand with abrasive paper P240 or with Troton’s unwoven abrasive fabric, degrease again (Silicone Remover Troton), prime with an adhesive promoter, such as Plastic Primer Troton. Due to the many different types of plastic, adhesion testing is advised. Do not apply the product directly on bare metal. Rangers should be applied on primed surfaces or on 2K topcoats and basecoats after proper preparation (be careful with the application on old coatings, thinner testing is advised). Always abrade, clean and degrease the surface before application.
• Do not apply the product on 1K primers. Instead, always prime the surfaces for the Rangers application with a 2k acrylic primer, 2K epoxy primer or 2k etching primer. Always wait the proper drying and hardening time of etching primer before application.
• Do not apply Rangers directly on bare original paint or directly on coatings of car body parts from the aftermarket.

Kit content:

• T1 STRONG POLISHING COMPOUND 250g
• T2 ANTIHOLOGRAM & MICROSCRATCH REMOVER 250g
• T3 QUICK WAX 500 ml
• T4 PROTECT LIQUID 250 ml

BRAYT T1 STRONG is a polishing compound dedicated to all types of varnish used in automotive and industry sector, including hard scratch resistant coatings (e.g. ceramic). Product is recommended to fresh polymerized coats and for old paint coatings. Removes easily scratches and sanding traces (abrasive paper 1500). Doesn’t contain fillers and silicones.

• Cut level 8/10
• Gloss level 8/10

BRAYT T2 Compound is designed for removing holograms and microscratches on painted surfaces as well as traces made in sanding process. Product guarantees ideal deep gloss, creates protective layer resistant to detergents on the surface of the clear coat. Doesn’t contain the silicone.

• Cut level 4/10
• Gloss level 10/10

BRAYT T3 QUICK WAX & SHINE simple and easy to use based on waxes, dedicated to all types of smooth and shiny surfaces (varnished, glass, plastic). It is possible with product to achieve gloss and color depth, surface becomes slippery. It shows great hydrophobic, nurturing and preserving properties. Doesn’t leave marks on plastic and rubber.

Properties: Gloss level 10/10

BRAYT T4 emulsion for surface refreshment, leaves invisible protective layer against impurities. Extends the freshness of the clear coat in 40-50%, decreases impurities on the car body up to 70-80%. Product might be used to protect varnished surfaces, gelcoats and polycarbonates. T4 has also light abrasive properties what allows to remove small defects and holograms. Suitable to gelcoats and each type of clear coats (acrylic, water based, bicomponent and fabric coatings), also on ceramic scratch resistant coatings. Enhances gloss, prevents the oxidation of the varnish, protects against UV rays, acid rain, resin. To achieve high gloss without the mist and holograms, soft foam is dedicated.

• Cut level 2/10
• Gloss level 10/10