2 column electrohydraulic lift

Suitable for repairing cars with internal combustion engines and electric cars.

This lift is suitable for repairing automatic transmissions, engines and the entire steering assembly, as it leaves the vehicle chassis completely free.

On hybrid and electric vehicles it is also easier to dismantle the battery pack and maintenance times are significantly reduced.

• Asymmetrical lifter without base with carrying crossbar
• Two lifting cylinders in pull that require no maintenance.
• Short arms with three front stages and rear stages for lifting even large vehicles and low profile.
• Minimum pad height of only 95 mm
• Safety valves for overloads and breakage of hydraulic pipes
• Descent speed control valve
• Mechanical support device with automatic insertion and manual disconnection
• Operation: electro-hydraulic

Big scissor lift

Suitable for tyre fitters to adjust wheel alignment and wheel camber. (LT version)

The scissor lift is also very suitable for carrying out routine maintenance on cars and vans.

This lift is suitable for repairing automatic transmissions, engines and the entire steering assembly, as it leaves the vehicle chassis completely free.

• Hydraulic parallelism of platforms and turrets
• Hydraulic safety in case of overload
• Hydraulic / mechanical safety in case of pipe breakage
• Emergency manual pump (OPTIONAL)
• Dead man controls, 24V
• Series 4 rubber pads

2 column electromechanical lift

Suitable for repairing cars with internal combustion engines and electric cars.

This lift is suitable for repairing automatic transmissions, engines and the entire steering assembly, as it leaves the vehicle chassis completely free.

On hybrid and electric vehicles it is also easier to dismantle the battery pack and maintenance times are significantly reduced.

• Lift with electronic synchronisation without baseframe for easy movement in the working area.
• The connecting cables can be fxed to the ceiling or recessed into the floor
• Electronic synchronisation between carriages to keep the height difference within max 24 mm
• Low voltage controls
• Short and long three-stage arms for the asymmetric lifting of vans and 4-wheel drive vehicles
• Pads min. height 85 mm.

Double scissor lifts

Suitable for tyre fitters. It leaves the wheels free for easy access.

Also ideal for standard car repairs as the chassis is completely free of obstacles.

Its height allows the operator to work in an upright position and therefore permits a wide range of uses.

• Easy to move up and down ramps
• Hydraulic synchronism of the platforms
• Hydraulic security
• Dead man controls, 24V
• Series of 4 standard rubber pads h = 60mm
• Safety command for the last section of descent with acoustic signal

2 column electrohydraulic lift

Suitable for repairing cars with internal combustion engines and electric cars.

This lift is suitable for repairing automatic transmissions, engines and the entire steering assembly, as it leaves the vehicle chassis completely free.

On hybrid and electric vehicles it is also easier to dismantle the battery pack and maintenance times are significantly reduced.

• Asymmetrical lifter without base with carrying crossbar
• Two lifting cylinders in pull that require no maintenance.
• Short arms with three front stages and rear stages for lifting even large vehicles and low profile.
• Minimum pad height of only 95 mm
• Safety valves for overloads and breakage of hydraulic pipes
• Descent speed control valve
• Mechanical support device with automatic insertion and manual disconnection
• Operation: electro-hydraulic

Big scissor lift

Suitable for tyre fitters to adjust wheel alignment and wheel camber. (LT version)

The scissor lift is also very suitable for carrying out routine maintenance on cars and vans.

This lift is suitable for repairing automatic transmissions, engines and the entire steering assembly, as it leaves the vehicle chassis completely free.

• Hydraulic parallelism of platforms and turrets
• Hydraulic safety in case of overload
• Hydraulic / mechanical safety in case of pipe breakage
• Emergency manual pump (OPTIONAL)
• Dead man controls, 24V
• Series 4 rubber pads

2 column electromechanical lift

Suitable for repairing cars with internal combustion engines and electric cars.

This lift is suitable for repairing automatic transmissions, engines and the entire steering assembly, as it leaves the vehicle chassis completely free.

On hybrid and electric vehicles it is also easier to dismantle the battery pack and maintenance times are significantly reduced.

• Lift with electronic synchronisation without baseframe for easy movement in the working area.
• The connecting cables can be fxed to the ceiling or recessed into the floor
• Electronic synchronisation between carriages to keep the height difference within max 24 mm
• Low voltage controls
• Short and long three-stage arms for the asymmetric lifting of vans and 4-wheel drive vehicles
• Pads min. height 85 mm.