Extrusion takes place on mandrel dies or mandrel-less. From the hose core via fabric reinforcement to extrusion of the hose cover, the blank is mounted on the mandrel die. The moulded hose is then vulcanized, demolded and cut to size. The resulting smooth or grooved surface is characteristic of extruded moulded hoses. Whether air conditioning, gas station, cooling/heating system or ventilation system - as specialists for moulded hoses, hose elbows and hose rings, we produce individually manufactured hose solutions in all required qualities.

Extruded hoses are square hoses typically used in HVAC systems or as vacuum hoses in automotive applications. They are designed to never flatten, regardless of bending or low pressure. These hoses are most advantageous in applications where hoses must be bent for prolonged periods of time, where hoses are required to hold low-pressure for long periods of time, or where cost is a critical component of manufacturing.

Molded hoses are always used when ordinary industrial hoses reach the limits of their range of applications. Our molded hoses fulfill almost all imaginable geometries and can easily carry practically all media, whether liquid, gaseous, containing oil or grease, aggressive, hot or cold. The starting material used withstands temperatures of up to 120 °C. If the material is reinforced with EPDM or silicone, loads of up to 200 °C are possible. We offer molded hoses with and without commercial reinforcements and spirals. Optionally, additional thread inserts, branches and, depending on the selection, fuel-resistant and chemical-resistant materials are available.

We offer a range of Rubber mounts suitable for various applications where a captive solution is required. Their simple design allows for easy installation, and restricts movement in both vertical directions thereby offering a good level of shock protection. Standard rubber mountings are manufactured in chloroprene rubber, which provides good resistance to oils and greases. Other rubber compounds can be offered to suit different environmental conditions. They are typically used in mobile generator and compressor installations, as engine and transmission mountings on automotive applications, and on marine equipment installations.

Rubber Bellows are an expandable/collapsible component to protect foreign particles. The bellow material should be well suited with outside (exposed to Atmosphere & ozone resistance) & inside conditions (Oil, grease & lubricants). The rubber bellows are a very important component of automobiles, especially the steering system of cars. Designed to keep dirt and debris out of the steering rack, rubber bellow is a cylindrical vessel that comes in a large variety of sizes, shapes, construction, and elastomer coated fabrics/ rubbers to suit diverse application requirements of vehicles.

Due to different annular convolutions, bellows are easily extensible & compressible and are appreciated for providing an excellent cushioning effect. Depending upon the end-use requirement rubber bellows are manufactured using various synthetic polymers such as SBR, Neoprene, NBR, Ethylene Propylene Diene Monomer (EPM, EPDM), etc.

Extrusion takes place on mandrel dies or mandrel-less. From the hose core via fabric reinforcement to extrusion of the hose cover, the blank is mounted on the mandrel die. The moulded hose is then vulcanized, demolded and cut to size. The resulting smooth or grooved surface is characteristic of extruded moulded hoses. Whether air conditioning, gas station, cooling/heating system or ventilation system - as specialists for moulded hoses, hose elbows and hose rings, we produce individually manufactured hose solutions in all required qualities.

Extruded hoses are square hoses typically used in HVAC systems or as vacuum hoses in automotive applications. They are designed to never flatten, regardless of bending or low pressure. These hoses are most advantageous in applications where hoses must be bent for prolonged periods of time, where hoses are required to hold low-pressure for long periods of time, or where cost is a critical component of manufacturing.

Molded hoses are always used when ordinary industrial hoses reach the limits of their range of applications. Our molded hoses fulfill almost all imaginable geometries and can easily carry practically all media, whether liquid, gaseous, containing oil or grease, aggressive, hot or cold. The starting material used withstands temperatures of up to 120 °C. If the material is reinforced with EPDM or silicone, loads of up to 200 °C are possible. We offer molded hoses with and without commercial reinforcements and spirals. Optionally, additional thread inserts, branches and, depending on the selection, fuel-resistant and chemical-resistant materials are available.

We offer a range of Rubber mounts suitable for various applications where a captive solution is required. Their simple design allows for easy installation, and restricts movement in both vertical directions thereby offering a good level of shock protection. Standard rubber mountings are manufactured in chloroprene rubber, which provides good resistance to oils and greases. Other rubber compounds can be offered to suit different environmental conditions. They are typically used in mobile generator and compressor installations, as engine and transmission mountings on automotive applications, and on marine equipment installations.